AirThings BLE Sensors¶
The airthings_wave_plus
and airthings_wave_mini
sensor platforms lets you track the output of AirThings Bluetooth Low Energy devices.
This component will track radon, airborne chemicals, CO2, temperature and humidity and others depending on the device sensors.
Device Discovery¶
AirThings devices can be found using the airthings_ble
ble scanner.
To find out your device’s MAC address, add the following to your ESPHome configuration:
logger:
level: DEBUG # Required for the tracker to show the device
esp32_ble_tracker:
airthings_ble:
The device will then listen for nearby devices, and display a message like this one:
[D][airthings_ble:019]:
Found AirThings device Serial: 123456789 (MAC: XX:XX:XX:XX:XX:XX)
Once the device is found, remove the airthings_ble
device tracker from your configuration and take note of the device MAC address, and use it when configuring a sensor below.
Supported Devices¶
Airthings Wave Plus Sensor¶
AirThings Wave Plus tracks radon (24h and long term), airborne chemicals, CO2, temperature, atmospheric pressure and humidity.
![../../_images/airthings_wave_plus.jpg](../../_images/airthings_wave_plus.jpg)
Configuration example:¶
sensor:
- platform: airthings_wave_plus
name: wave_plus
ble_client_id: airthings01
update_interval: 5min # default
battery_update_interval: 24h # default
temperature:
name: "WavePlus Temperature"
radon:
name: "WavePlus Radon"
radon_long_term:
name: "WavePlus Radon Long Term"
pressure:
name: "WavePlus Pressure"
humidity:
name: "WavePlus Humidity"
co2:
name: "WavePlus CO2"
tvoc:
name: "WavePlus VOC"
illuminance:
name: "WavePlus ambient light"
battery_voltage:
name: "WavePlus Battery Voltage"
ble_client:
- mac_address: XX:XX:XX:XX:XX:XX
id: airthings01
esp32_ble_tracker:
Airthings Wave Mini Sensor¶
AirThings Wave Mini tracks airborne chemicals, temperature, pressure and humidity.
![../../_images/airthings_wave_mini.jpg](../../_images/airthings_wave_mini.jpg)
Configuration example:
sensor:
- platform: airthings_wave_mini
ble_client_id: airthingsmini
update_interval: 5min # default
battery_update_interval: 24h # default
temperature:
name: "WaveMini Temperature"
pressure:
name: "WaveMini Pressure"
humidity:
name: "WaveMini Humidity"
tvoc:
name: "WaveMini VOC"
battery_voltage:
name: "WaveMini Battery Voltage"
ble_client:
- mac_address: XX:XX:XX:XX:XX:XX
id: airthingsmini
esp32_ble_tracker:
Note
The sensor uses active polling of devices every 5 minutes as per the device reported internal refresh timeout.
Note
Battery-voltage reporting defaults to once every 24 hours in order
to reduce BLE traffic (obtaining the battery voltage requires quite
a few BLE commands/responses); if you wish to have it reported
more frequently configure the battery_update_interval
. The main
sensor update_interval
controls the overall polling frequency
so setting the interval for the battery voltage to a lower value
will result in the battery voltage being reported once per polling
interval.
Battery Level Reporting¶
If you wish to have the ‘percentage of battery life remaining’ reported as a sensor, you can make use of the Copy Sensor component.
The examples below are based on standard alkaline-chemistry batteries; if you use other types of batteries you may need to adjust the reference voltages to obtain a proper 0-100% scale. The voltage references were chosen to closely match the 0-100% range displayed by the AirThings mobile app.
sensor:
- platform: airthings_wave_mini
ble_client_id: airthingsmini
battery_voltage:
id: bv
name: "WaveMini Battery Voltage"
- platform: copy
source_id: bv
name: "WaveMini Battery Level"
unit_of_measurement: "%"
device_class: battery
accuracy_decimals: 0
filters:
- calibrate_linear:
- 2.7 -> 0
- 4.5 -> 100
sensor:
- platform: airthings_wave_plus
ble_client_id: airthings01
battery_voltage:
id: bv
name: "WavePlus Battery Voltage"
- platform: copy
source_id: bv
name: "WavePlus Battery Level"
unit_of_measurement: "%"
device_class: battery
accuracy_decimals: 0
filters:
- calibrate_linear:
- 2.2 -> 0
- 3.1 -> 100