|
| | ADS1118 ()=default |
| |
| void | setup () override |
| |
| void | dump_config () override |
| |
| float | get_setup_priority () const override |
| |
| float | request_measurement (ADS1118Multiplexer multiplexer, ADS1118Gain gain, bool temperature_mode) |
| | Helper method to request a measurement from a sensor. More...
|
| |
| virtual void | loop () |
| | This method will be called repeatedly. More...
|
| |
| float | get_actual_setup_priority () const |
| |
| void | set_setup_priority (float priority) |
| |
| virtual float | get_loop_priority () const |
| | priority of loop(). More...
|
| |
| void | call () |
| |
| virtual void | on_shutdown () |
| |
| virtual void | on_safe_shutdown () |
| |
| uint32_t | get_component_state () const |
| |
| virtual void | mark_failed () |
| | Mark this component as failed. More...
|
| |
| bool | is_failed () const |
| |
| bool | is_ready () const |
| |
| virtual bool | can_proceed () |
| |
| bool | status_has_warning () const |
| |
| bool | status_has_error () const |
| |
| void | status_set_warning (const char *message="unspecified") |
| |
| void | status_set_error (const char *message="unspecified") |
| |
| void | status_clear_warning () |
| |
| void | status_clear_error () |
| |
| void | status_momentary_warning (const std::string &name, uint32_t length=5000) |
| |
| void | status_momentary_error (const std::string &name, uint32_t length=5000) |
| |
| bool | has_overridden_loop () const |
| |
| void | set_component_source (const char *source) |
| | Set where this component was loaded from for some debug messages. More...
|
| |
| const char * | get_component_source () const |
| | Get the integration where this component was declared as a string. More...
|
| |
| | SPIDevice () |
| |
| | SPIDevice (SPIComponent *parent, GPIOPin *cs_pin) |
| |
| void | spi_setup () override |
| |
| void | spi_teardown () override |
| |
| void | set_spi_parent (SPIComponent *parent) |
| |
| void | set_cs_pin (GPIOPin *cs) |
| |
| void | set_data_rate (uint32_t data_rate) |
| |
| void | set_bit_order (SPIBitOrder order) |
| |
| void | set_mode (SPIMode mode) |
| |
| uint8_t | read_byte () |
| |
| void | read_array (uint8_t *data, size_t length) |
| |
| void | write (uint16_t data, size_t num_bits) |
| | Write a single data item, up to 32 bits. More...
|
| |
| void | write_cmd_addr_data (size_t cmd_bits, uint32_t cmd, size_t addr_bits, uint32_t address, const uint8_t *data, size_t length, uint8_t bus_width=1) |
| |
| void | write_byte (uint8_t data) |
| |
| void | transfer_array (uint8_t *data, size_t length) |
| | Write the array data, replace with received data. More...
|
| |
| void | transfer_array (std::array< uint8_t, N > &data) |
| |
| uint8_t | transfer_byte (uint8_t data) |
| |
| void | write_byte16 (uint16_t data) |
| | Write 16 bit data. More...
|
| |
| void | write_array16 (const uint16_t *data, size_t length) |
| | Write an array of data as 16 bit values, byte-swapping if required. More...
|
| |
| void | enable () |
| |
| void | disable () |
| |
| void | write_array (const uint8_t *data, size_t length) |
| |
| void | write_array (const std::array< uint8_t, N > &data) |
| |
| void | write_array (const std::vector< uint8_t > &data) |
| |
| | SPIClient (SPIBitOrder bit_order, SPIMode mode, uint32_t data_rate) |
| |
| bool | spi_is_ready () |
| |
|
| virtual void | call_loop () |
| |
| virtual void | call_setup () |
| |
| virtual void | call_dump_config () |
| |
| void | set_interval (const std::string &name, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a unique name. More...
|
| |
| void | set_interval (uint32_t interval, std::function< void()> &&f) |
| |
| bool | cancel_interval (const std::string &name) |
| | Cancel an interval function. More...
|
| |
| void | set_retry (const std::string &name, uint32_t initial_wait_time, uint8_t max_attempts, std::function< RetryResult(uint8_t)> &&f, float backoff_increase_factor=1.0f) |
| | Set an retry function with a unique name. More...
|
| |
| void | set_retry (uint32_t initial_wait_time, uint8_t max_attempts, std::function< RetryResult(uint8_t)> &&f, float backoff_increase_factor=1.0f) |
| |
| bool | cancel_retry (const std::string &name) |
| | Cancel a retry function. More...
|
| |
| void | set_timeout (const std::string &name, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a unique name. More...
|
| |
| void | set_timeout (uint32_t timeout, std::function< void()> &&f) |
| |
| bool | cancel_timeout (const std::string &name) |
| | Cancel a timeout function. More...
|
| |
| void | defer (const std::string &name, std::function< void()> &&f) |
| | Defer a callback to the next loop() call. More...
|
| |
| void | defer (std::function< void()> &&f) |
| | Defer a callback to the next loop() call. More...
|
| |
| bool | cancel_defer (const std::string &name) |
| | Cancel a defer callback using the specified name, name must not be empty. More...
|
| |
Definition at line 30 of file ads1118.h.
Public Member Functions inherited from esphome::Component